Configurasi EIRP di Cisco Packet Tracer



awal mula kita buat seperti gambar di bawah ini, yang menggunakan 3 buah router , dan 3 buah PC (Client)
...



Setelah itu,
kita berikan IP Address pada ketiga PC Client,
- gambar di bawah merupakan pemberian IP address pada PC0,

- gambar di bawah merupakan pemberian IP address pada PC1,



- gambar di bawah merupakan pemberian IP address pada PC0 ..


Setelah kita berikan IP Address pada ketiga PC Client ..

Selanjutnya,
Pemberian IP Interface pada Router 1


--- System Configuration Dialog ---

Continue with configuration dialog? [yes/no]: no


Press RETURN to get started!

Router>enable
Router#configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)#int fa0/0
Router(config-if)#ip add 192.168.21.1 255.255.255.0
Router(config-if)#no shut

%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up

Router(config-if)#ex
Router(config)#int se2/0
Router(config-if)#ip add 10.10.10.1 255.0.0.0
Router(config-if)#no shut

%LINK-5-CHANGED: Interface Serial3/0, changed state to down
Router(config-if)#ex
Router(config)#ex
Router#
%SYS-5-CONFIG_I: Configured from console by console
wr
Building configuration...
[OK]
Router#

Configurasi EIGRP pada Router 1

Router>en
Router#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)#router eigrp 1
Router(config-router)#net 192.168.21.1
Router(config-router)#net 10.10.10.1
Router(config-router)#ex
Router(config)#ex
Router#
%SYS-5-CONFIG_I: Configured from console by console
wr
Building configuration...
[OK]


selanjutnya,

Pemberian IP Interface pada Router 2

--- System Configuration Dialog ---

Continue with configuration dialog? [yes/no]: no


Press RETURN to get started!



Router>enable
Router#configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)#int fa0/0
Router(config-if)#ip add 192.168.40.1 255.255.255.0
Router(config-if)#no shut

%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up

Router(config-if)#ex
Router(config)#int se2/0
Router(config-if)#ip add 10.10.10.2 255.0.0.0
Router(config-if)#cl ra 64000
Router(config-if)#no shut

%LINK-5-CHANGED: Interface Serial2/0, changed state to up

Router(config-if)#ex
Router(config)#int se3/0
Router(config-if)#ip add 172.16.1.1 255.255.0.0
Router(config-if)#cl ra 64000
Router(config-if)#no shut

%LINK-5-CHANGED: Interface Serial3/0, changed state to down
Router(config-if)#ex
Router(config)#ex
Router#
%SYS-5-CONFIG_I: Configured from console by console
wr
Building configuration...
[OK]
Router#
Configurasi EIGRP pada Router 2

Router>enable
Router#configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)#router eigrp 1
Router(config-router)#net 10.10.10.2
Router(config-router)#net 192.168.40.1
Router(config-router)#net 172.16.1.1
Router(config-router)#ex
Router(config)#ex
Router#
%SYS-5-CONFIG_I: Configured from console by console
wr
Building configuration...
[OK]
Router#

dan yang terakhir, 

Pemberian IP Interface pada Router 3

--- System Configuration Dialog ---

Continue with configuration dialog? [yes/no]: no


Press RETURN to get started!



Router>enable
Router#configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)#int fa0/0
Router(config-if)#ip add 192.168.60.1 255.255.255.0
Router(config-if)#no shut

%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up

Router(config-if)#ex
Router(config)#int se2/0
Router(config-if)#ip add 172.16.1.2 255.255.0.0
Router(config-if)#no shut

%LINK-5-CHANGED: Interface Serial2/0, changed state to up

Router(config-if)#ex
Router(config)#ex
Router#
%SYS-5-CONFIG_I: Configured from console by console
wr
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial2/0, changed state to up

Building configuration...
[OK]
Router#

Configurasi EIGRP pada Router 3

Router>enable
Router#configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)#router eigrp 1
Router(config-router)#net 192.168.60.1
Router(config-router)#net 172.16.1.2
Router(config-router)#ex
Router(config)#ex
Router#
%SYS-5-CONFIG_I: Configured from console by console
wr
Building configuration...
[OK]
Router#



Setelah semua kita beri IP Address di Komputer dan Configurasi EIGRP pada semua Router..
Seperti gambar dibawah, Kita coba PING antara PC Client (PC1 ke PC2 dan Sebaliknya)...



 demikian tutorial Configurasi EIRP di Cisco Packet Tracer yang saya buat, Apabila ada yang kurang jelas bisa di tanyakan.....


Diposting oleh Unknown di 22.25 1 komentar

 

Konfigurasi RIP di Packet Trecer

Assalam buat kita semua.......!!!

    Sebelum melakukan Konfigurasi RIP di Packet Trecer hendaknya kita memiliki software Packet Trecer yng sudah terinsstall di PC maupun di Laptop!!
langsung saja kita mulai yang pertama-tama buka aplikasi disainnya atau aplikasinya!! kemudian lakukan disain seprti yang kita mau! ini sebagi contohnya!!
   Setelah melakukan disan dan menepatkan posisi yang kita mau kemudian lakukan pemberian IP addres di setiap PC yang ada pada gambar diatas dan memasukan ip addres secara static alias manual
   a. PC 1
      IP addres 191.168.80.8
      Subnet Mask 255.255.0.0
      Gateway 191.168.80.1
   b. PC 2
      IP addres 200.168.60.6
      Subnet Mask 255.255.255.0
      Gateway 200.168.60.1
   c. PC 3
      IP addres 202.168.22.2
      Subnet Mask 255.255.255.0
      Gateway 202.168.22.1
   IP yang tertera di atas bisa kita rubah sesuai yng kita inginkan aslkan mudah untuk di ingat dan di pahami intinya IP yang ada di setiap PC bisa diberikan sesuka kita dengan catatan di setiap PC tidak boleh sama sebagai contoh seperti di atas.
   Kemudian kita lakukan konfigurasi Router 1 s/d Router 3 dengan cara double klik mouse pada Router dan klik menu CLI lakukan konfigurasi Router 1 seperti di bawah:


Router 1
         --- System Configuration Dialog ---

Continue with configuration dialog? [yes/no]: no

Press RETURN to get started!

Router>enable
Router#configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)#interface Fastethernet0/0
Router(config-if)#ip add 191.168.80.1 255.255.255.0
Router(config-if)#no shutdown

%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up

Router(config-if)#exite
Router(config)#interface serial2/0
Router(config-if)#ip add 10.10.10.1 255.0.0.0
Router(config-if)#band 125
Router(config-if)#clock rate 125000
Router(config-if)#no shutdown

%LINK-5-CHANGED: Interface Serial2/0, changed state to down
Router(config-if)#exite
Router(config)#router rip
Router(config-router)#net 191.168.80.1
Router(config-router)#net 10.10.10.1
Router(config-router)#exite
Router(config)#exite
Router#
%SYS-5-CONFIG_I: Configured from console by console
write
Building configuration...
[OK]
Router#

Router 2
Router>enable
Router#configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)#interface Fastethernet 0/0
Router(config-if)#ip add 200.168.60.1 255.255.255.0
Router(config-if)#no shutdown

%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up

Router(config-if)#exite
Router(config)#interface serial2/0
Router(config-if)#ip add 10.10.10.2 255.0.0.0
Router(config-if)#band 125
Router(config-if)#no shutdown

Router(config-if)#
%LINK-5-CHANGED: Interface Serial2/0, changed state to up

Router(config-if)#exite
Router(config)#
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial2/0, changed state to up

Router(config)#intface serial3/0
Router(config-if)#ip add 172.16.6.1 255.255.0.0
Router(config-if)#band 125
Router(config-if)#clock rate 125000
Router(config-if)#no shutdown

%LINK-5-CHANGED: Interface Serial3/0, changed state to down
Router(config-if)#exite
Router(config)#router rip
Router(config-router)#net 200.168.60.1
Router(config-router)#net 10.10.10.2
Router(config-router)#net 172.16.6.1
Router(config-router)#exite
Router(config)#exite
Router#
%SYS-5-CONFIG_I: Configured from console by console
write
Building configuration...
[OK]
Router#

Router 3
Router>enable
Router#configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)#intface  Fastethernet0/0
Router(config-if)#ip add 202.168.22.1 255.255.255.0
Router(config-if)#no shutdown

%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up

Router(config-if)#
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up

Router(config-if)#exite
Router(config)#intface serial2/0
Router(config-if)#ip add 172.16.6.2 255.255.0.0
Router(config-if)#band 125
Router(config-if)#no shutdown

Router(config-if)#
%LINK-5-CHANGED: Interface Serial2/0, changed state to up

Router(config-if)#exite
Router(config)#router rip
Router(config-router)#net 202.168.22.1
Router(config-router)#net 172.16.6.2
Router(config-router)#exite
Router(config)#exite
Router#
%SYS-5-CONFIG_I: Configured from console by console
write
Building configuration...
[OK]
Router#


Diposting oleh Unknown di 11.41 0 komentar

 
Langganan: Postingan (Atom)