Configurasi EIRP di Cisco Packet Tracer



awal mula kita buat seperti gambar di bawah ini, yang menggunakan 3 buah router , dan 3 buah PC (Client)
...



Setelah itu,
kita berikan IP Address pada ketiga PC Client,
- gambar di bawah merupakan pemberian IP address pada PC0,

- gambar di bawah merupakan pemberian IP address pada PC1,



- gambar di bawah merupakan pemberian IP address pada PC0 ..


Setelah kita berikan IP Address pada ketiga PC Client ..

Selanjutnya,
Pemberian IP Interface pada Router 1


--- System Configuration Dialog ---

Continue with configuration dialog? [yes/no]: no


Press RETURN to get started!

Router>enable
Router#configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)#int fa0/0
Router(config-if)#ip add 192.168.21.1 255.255.255.0
Router(config-if)#no shut

%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up

Router(config-if)#ex
Router(config)#int se2/0
Router(config-if)#ip add 10.10.10.1 255.0.0.0
Router(config-if)#no shut

%LINK-5-CHANGED: Interface Serial3/0, changed state to down
Router(config-if)#ex
Router(config)#ex
Router#
%SYS-5-CONFIG_I: Configured from console by console
wr
Building configuration...
[OK]
Router#

Configurasi EIGRP pada Router 1

Router>en
Router#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)#router eigrp 1
Router(config-router)#net 192.168.21.1
Router(config-router)#net 10.10.10.1
Router(config-router)#ex
Router(config)#ex
Router#
%SYS-5-CONFIG_I: Configured from console by console
wr
Building configuration...
[OK]


selanjutnya,

Pemberian IP Interface pada Router 2

--- System Configuration Dialog ---

Continue with configuration dialog? [yes/no]: no


Press RETURN to get started!



Router>enable
Router#configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)#int fa0/0
Router(config-if)#ip add 192.168.40.1 255.255.255.0
Router(config-if)#no shut

%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up

Router(config-if)#ex
Router(config)#int se2/0
Router(config-if)#ip add 10.10.10.2 255.0.0.0
Router(config-if)#cl ra 64000
Router(config-if)#no shut

%LINK-5-CHANGED: Interface Serial2/0, changed state to up

Router(config-if)#ex
Router(config)#int se3/0
Router(config-if)#ip add 172.16.1.1 255.255.0.0
Router(config-if)#cl ra 64000
Router(config-if)#no shut

%LINK-5-CHANGED: Interface Serial3/0, changed state to down
Router(config-if)#ex
Router(config)#ex
Router#
%SYS-5-CONFIG_I: Configured from console by console
wr
Building configuration...
[OK]
Router#
Configurasi EIGRP pada Router 2

Router>enable
Router#configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)#router eigrp 1
Router(config-router)#net 10.10.10.2
Router(config-router)#net 192.168.40.1
Router(config-router)#net 172.16.1.1
Router(config-router)#ex
Router(config)#ex
Router#
%SYS-5-CONFIG_I: Configured from console by console
wr
Building configuration...
[OK]
Router#

dan yang terakhir, 

Pemberian IP Interface pada Router 3

--- System Configuration Dialog ---

Continue with configuration dialog? [yes/no]: no


Press RETURN to get started!



Router>enable
Router#configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)#int fa0/0
Router(config-if)#ip add 192.168.60.1 255.255.255.0
Router(config-if)#no shut

%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up

Router(config-if)#ex
Router(config)#int se2/0
Router(config-if)#ip add 172.16.1.2 255.255.0.0
Router(config-if)#no shut

%LINK-5-CHANGED: Interface Serial2/0, changed state to up

Router(config-if)#ex
Router(config)#ex
Router#
%SYS-5-CONFIG_I: Configured from console by console
wr
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial2/0, changed state to up

Building configuration...
[OK]
Router#

Configurasi EIGRP pada Router 3

Router>enable
Router#configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)#router eigrp 1
Router(config-router)#net 192.168.60.1
Router(config-router)#net 172.16.1.2
Router(config-router)#ex
Router(config)#ex
Router#
%SYS-5-CONFIG_I: Configured from console by console
wr
Building configuration...
[OK]
Router#



Setelah semua kita beri IP Address di Komputer dan Configurasi EIGRP pada semua Router..
Seperti gambar dibawah, Kita coba PING antara PC Client (PC1 ke PC2 dan Sebaliknya)...



 demikian tutorial Configurasi EIRP di Cisco Packet Tracer yang saya buat, Apabila ada yang kurang jelas bisa di tanyakan.....


Penulis : Unknown ~ Sebuah blog yang menyediakan berbagai macam informasi

Artikel Configurasi EIRP di Cisco Packet Tracer ini dipublish oleh Unknown pada hari Sabtu, 29 Desember 2012. Semoga artikel ini dapat bermanfaat.Terimakasih atas kunjungan Anda silahkan tinggalkan komentar.sudah ada 1komentar: di postingan Configurasi EIRP di Cisco Packet Tracer
 

1 komentar:

Langganan: Posting Komentar (Atom)