Sebelum melakukan Konfigurasi RIP di Packet Trecer hendaknya kita memiliki software Packet Trecer yng sudah terinsstall di PC maupun di Laptop!!
langsung saja kita mulai yang pertama-tama buka aplikasi disainnya atau aplikasinya!! kemudian lakukan disain seprti yang kita mau! ini sebagi contohnya!!
a. PC 1
IP addres 191.168.80.8
Subnet Mask 255.255.0.0
Gateway 191.168.80.1
b. PC 2
IP addres 200.168.60.6
Subnet Mask 255.255.255.0
Gateway 200.168.60.1
c. PC 3
IP addres 202.168.22.2
Subnet Mask 255.255.255.0
Gateway 202.168.22.1
IP yang tertera di atas bisa kita rubah sesuai yng kita inginkan aslkan mudah untuk di ingat dan di pahami intinya IP yang ada di setiap PC bisa diberikan sesuka kita dengan catatan di setiap PC tidak boleh sama sebagai contoh seperti di atas.
Kemudian kita lakukan konfigurasi Router 1 s/d Router 3 dengan cara double klik mouse pada Router dan klik menu CLI lakukan konfigurasi Router 1 seperti di bawah:
Router 1
--- System
Configuration Dialog ---
Continue with configuration dialog? [yes/no]: no
Press RETURN to get started!
Router>enable
Router#configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#interface Fastethernet0/0
Router(config-if)#ip add 191.168.80.1 255.255.255.0
Router(config-if)#no shutdown
%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to
up
%LINEPROTO-5-UPDOWN: Line protocol on Interface
FastEthernet0/0, changed state to up
Router(config-if)#exite
Router(config)#interface serial2/0
Router(config-if)#ip add 10.10.10.1 255.0.0.0
Router(config-if)#band 125
Router(config-if)#clock rate 125000
Router(config-if)#no shutdown
%LINK-5-CHANGED: Interface Serial2/0, changed state to down
Router(config-if)#exite
Router(config)#router rip
Router(config-router)#net 191.168.80.1
Router(config-router)#net 10.10.10.1
Router(config-router)#exite
Router(config)#exite
Router#
%SYS-5-CONFIG_I: Configured from console by console
write
Building configuration...
[OK]
Router#
Router 2
Router>enable
Router#configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#interface Fastethernet 0/0
Router(config-if)#ip add 200.168.60.1 255.255.255.0
Router(config-if)#no shutdown
%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to
up
%LINEPROTO-5-UPDOWN: Line protocol on Interface
FastEthernet0/0, changed state to up
Router(config-if)#exite
Router(config)#interface serial2/0
Router(config-if)#ip add 10.10.10.2 255.0.0.0
Router(config-if)#band 125
Router(config-if)#no shutdown
Router(config-if)#
%LINK-5-CHANGED: Interface Serial2/0, changed state to up
Router(config-if)#exite
Router(config)#
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial2/0,
changed state to up
Router(config)#intface serial3/0
Router(config-if)#ip add 172.16.6.1 255.255.0.0
Router(config-if)#band 125
Router(config-if)#clock rate 125000
Router(config-if)#no shutdown
%LINK-5-CHANGED: Interface Serial3/0, changed state to down
Router(config-if)#exite
Router(config)#router rip
Router(config-router)#net 200.168.60.1
Router(config-router)#net 10.10.10.2
Router(config-router)#net 172.16.6.1
Router(config-router)#exite
Router(config)#exite
Router#
%SYS-5-CONFIG_I: Configured from console by console
write
Building configuration...
[OK]
Router#
Router 3
Router>enable
Router#configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#intface Fastethernet0/0
Router(config-if)#ip add 202.168.22.1 255.255.255.0
Router(config-if)#no shutdown
%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to
up
Router(config-if)#
%LINEPROTO-5-UPDOWN: Line protocol on Interface
FastEthernet0/0, changed state to up
Router(config-if)#exite
Router(config)#intface serial2/0
Router(config-if)#ip add 172.16.6.2 255.255.0.0
Router(config-if)#band 125
Router(config-if)#no shutdown
Router(config-if)#
%LINK-5-CHANGED: Interface Serial2/0, changed state to up
Router(config-if)#exite
Router(config)#router rip
Router(config-router)#net 202.168.22.1
Router(config-router)#net 172.16.6.2
Router(config-router)#exite
Router(config)#exite
Router#
%SYS-5-CONFIG_I: Configured from console by console
write
Building configuration...
[OK]
Router#
0 komentar:
Posting Komentar